Electrical switchgear cabinets arranged across a large indoor space
APPLICATIONS

Medium Voltage Switchgear for Industrial Facilities.

New electrical distribution equipment built around your project. Discuss specifications, timing and delivery with a U.S. manufacturer.

01 BUILT FOR THE WORK AHEADEquipment photograph shown for illustration.
01 /
MADE IN USAAmerican components
02 /
UL 891Low-voltage switchboards
03 /
SHORT LEAD TIMESSchedule-focused planning
04 /
NATIONWIDEShipping available
01 /

Match the Switchgear to the Facility’s Distribution Plan

Industrial medium-voltage switchgear must fit the facility’s electrical architecture, not just a nominal voltage. Start with the one-line diagram and define the incoming source, bus arrangement, feeder count, protective devices, metering, and any tie or future positions. These choices affect available fault-current coordination, operating flexibility, footprint, and the sequence for isolating equipment during maintenance. Identify connected loads such as motors, transformers, process lines, and large drives, because starting behavior and load criticality can influence protection and switching requirements. Document the system voltage, frequency, grounding method, fault-current data, and operating scenarios for engineering review. If utility or plant standards impose specific requirements, include them early; assumptions left unresolved can lead to redesign, procurement changes, or equipment that does not suit the intended system.

02 /

Specify Protection Around Real Operating Conditions

Protection settings and device selection depend on the facility’s actual system study, not a generic switchgear schedule. Provide the latest short-circuit, coordination, and arc-flash study information when available, and identify upstream and downstream devices that must coordinate with the new lineup. Changes in transformers, generators, utility service, or parallel operating modes can alter fault current and protection behavior, so note both normal and alternate configurations. Clarify relay functions, instrument transformer requirements, control power, trip circuits, communications, and whether interfaces to plant monitoring or control systems are needed. These details matter because incomplete protection criteria can leave engineers unable to verify selectivity or integration. Final ratings, equipment selection, and protection applicability require project-specific evaluation against the system data and governing requirements.

Copper busbars inside electrical equipment, shown for illustration
THE DETAILS BEHIND THE POWERIllustrative photograph; not represented as our facility. Photo: ToT89.
03 /

Plan the Lineup Around Process Continuity

A switchgear replacement or plant expansion is constrained by the production schedule as much as by the electrical design. Determine which loads can be interrupted, which processes require an approved shutdown window, and whether temporary arrangements are part of the project scope. Record the existing lineup’s dimensions, cable entry locations, bus connections, working clearances, access routes, and known interface conditions before settling the new arrangement. A drawing that fits the electrical room but blocks cable termination access or removal of a breaker can create costly field changes. Coordinate layout reviews with facility operations, electrical engineering, and the installation contractor. Any tie-in, transfer, or cutover plan must be engineered and executed by qualified personnel under approved procedures; all work requiring de-energization must be planned accordingly.

04 /

Resolve Site Conditions and Installation Interfaces

Industrial environments can impose requirements beyond the electrical rating: dust, moisture, corrosive exposure, temperature, vibration, elevation, or limited ventilation may affect enclosure selection and installation planning. Describe the actual room or outdoor location, including environmental conditions, access restrictions, floor loading information when available, and any applicable site standards. Confirm cable types and termination approach, grounding connections, conduit or busway interfaces, control wiring, and the location of incoming and outgoing circuits. These interfaces matter because a mismatch can delay setting equipment, complicate cable work, or require unplanned modifications. Provide existing equipment drawings and field dimensions where possible, while identifying measurements that still need verification. The manufacturer and project team can then review the configuration; final suitability remains subject to engineering review and the project’s applicable codes and specifications.

05 /

Prepare a Complete RFQ and Review Package

A useful request for quotation gives the manufacturer enough information to identify open engineering decisions rather than hiding them in assumptions. Include the one-line diagram, load and feeder schedule, electrical studies, equipment arrangement, applicable specifications, preferred component requirements, and control or communications documents. State which items are mandatory and which are preferences, and mark known deviations or unanswered questions. Ask the project team to review submittal drawings, bills of material, wiring diagrams, and interface details against the design before release for production. Clear document ownership and revision control reduce the risk of building from superseded information. A U.S. manufacturer can discuss a custom-built assembly and American component options, but exact design, ratings, standards, compatibility, and availability must be confirmed for the individual project.

06 /

Coordinate Production Timing, Shipment, and Receipt

Discuss schedule expectations when requesting a quote, because engineering approvals, component selection, drawing revisions, and release for production can all affect the project sequence. Identify required approval dates, site readiness, delivery constraints, and any planned shutdown or construction milestones; avoid treating an estimated delivery period as a guarantee until scope and availability are confirmed. For nationwide shipment, coordinate the delivery address, receiving hours, unloading equipment, route or doorway limits, staging area, and storage conditions before the lineup is dispatched. Verify who will inspect the shipment, document visible damage, and manage any discrepancy. These practical steps matter because switchgear is substantial equipment that may be difficult to move or store after arrival. Confirm packaging, shipment configuration, and delivery arrangements with the project team for the specific order.

THE DETAILS MATTER

Project
specifications.

Bring your requirements to the conversation. Final configurations are determined by the project scope and applicable standards.

Specifications and project considerations
ParameterProject consideration
ApplicationMedium Voltage Switchgear for Industrial Facilities
Voltage and configurationProject-specific; confirm in quotation
Continuous current and busProject-specific; confirm in quotation
Short-circuit ratingProject-specific; confirm in quotation
Standards and certificationAs applicable; verify for the proposed assembly
Component originAll-American options; confirm in quotation
Lead time and shippingProject-specific; nationwide shipping available
LET'S BUILD SOMETHING

Your project
starts here.

Tell us what you are planning. Share the details you have, and start a conversation about new equipment built for the job.

PREFER TO TALK?
(951) 403-5738
HOUSTON, TEXAS / NATIONWIDE
PROJECT INQUIRY

Request a quote

Fields marked with an asterisk are required.

Submitting opens your email application with your inquiry. Please send the prepared email to complete your request; no information is submitted through this website.

REQUEST A QUOTE