Close view of gray switchgear cabinets with breakers on wooden pallets
PLANNING GUIDES

Switchgear Interlocks Explained.

New electrical distribution equipment built around your project. Discuss specifications, timing and delivery with a U.S. manufacturer.

01 BUILT FOR THE WORK AHEADEquipment photograph shown for illustration.
01 /
MADE IN USAAmerican components
02 /
UL 891Low-voltage switchboards
03 /
SHORT LEAD TIMESSchedule-focused planning
04 /
NATIONWIDEShipping available
01 /

What an Interlock Prevents—and What It Does Not

A switchgear interlock is a mechanical, electrical, or coordinated system intended to prevent a defined, unsafe operating sequence. For example, a design may block access to a compartment until specified conditions are met, or prevent two sources from being connected in parallel when the system is not designed for that arrangement. The exact function depends on the one-line diagram, equipment arrangement, operating procedure, and interlock scheme. An interlock is not a substitute for protective relaying, lockout/tagout, verification of absence of voltage, or qualified work practices. During planning, identify each hazardous sequence the design must prevent and the operating conditions involved. This keeps the specification focused on a verifiable function rather than a vague request for “interlocked gear.”

02 /

Choose the Scheme Around the Operating Sequence

Start with how operators are expected to transfer, isolate, or access equipment—not with a preferred interlock device. A main-tie-main arrangement, generator connection, maintenance bypass, or drawout breaker lineup can each create different sequencing needs. Document normal and alternate source conditions, permitted switching paths, and any circumstances in which parallel operation is allowed or prohibited. Then have the engineering team determine whether mechanical keys, electrical permissives, trapped-key arrangements, or a combination are appropriate for the equipment and control scheme. These methods are not interchangeable in every application: wiring, loss of control power, component access, and maintenance can affect their behavior. Resolve the intended sequence early so the manufacturer can assess the design and identify interface questions before drawings are finalized.

Copper busbars inside electrical equipment, shown for illustration
THE DETAILS BEHIND THE POWERIllustrative photograph; not represented as our facility. Photo: ToT89.
03 /

Define Boundaries, Devices, and Failure Conditions

A useful procurement specification names the equipment and devices covered by each interlock, along with the state that permits or blocks an operation. Include relevant breakers, disconnects, doors, shutters, control switches, alternate sources, and external equipment where applicable. Clarify what should happen if control power is unavailable, a signal is missing, or a device is in an intermediate position; do not assume the desired response is self-evident. Where the scheme crosses the switchgear boundary, identify who supplies and wires each component and who verifies the interface. These details matter because an interlock can appear complete on a panel schedule while depending on a field device or signal that is absent from the purchase scope. Confirming boundaries reduces redesign, change orders, and commissioning confusion.

04 /

Coordinate the Interlock With Drawings and Controls

Interlock requirements should appear consistently across the one-line diagram, elementary and wiring diagrams, equipment specifications, control narratives, and sequence-of-operation documents. A mismatch—such as a drawing that permits an operation the narrative prohibits—can delay review or leave installers without a clear basis for wiring. For custom equipment, provide available source and load information, breaker arrangement, control-power details, external permissive signals, and the intended operating sequence. Mark items that remain preliminary instead of allowing an assumption to look approved. During submittal review, check device tags, terminal points, keying logic, and responsibility for field connections against the same design basis. A controlled set of documents gives the manufacturer, electrical contractor, controls team, and commissioning personnel a shared reference for resolving discrepancies.

05 /

Plan for Operations, Maintenance, and Commissioning

An interlock that is technically correct can still cause operating problems if its logic is unfamiliar or its release procedure is unclear. Consider who will perform routine transfers, how maintenance isolation will be handled, whether an authorized override is part of the approved design, and how operators will recognize an interlock condition. Any bypass or override must be deliberately specified, controlled, and addressed by the facility’s safety procedures; it should not be treated as a casual workaround. Include the intended functional checks in commissioning documents and confirm who will witness and record them. Tests should verify the specified sequence and interfaces under approved, de-energized conditions where required by the work plan. Clear operating instructions and test records help preserve the design intent after turnover.

06 /

Align Procurement, Delivery, and Site Readiness

Interlock design can affect enclosure layout, control wiring, accessory selection, and coordination with upstream or downstream equipment, so unresolved operating decisions may hold up engineering release or create late revisions. When requesting a quote, send the current one-line diagram, equipment schedule, written sequence, applicable project standards, and known site interfaces; identify the expected review and approval path. Discuss the required delivery window with the U.S. manufacturer, but treat schedule and availability as project-specific rather than guaranteed. Before shipment, coordinate access route, receiving capacity, unloading equipment, indoor storage, and the installation sequence with the site team. Confirm the shipping configuration and delivery constraints against the actual route, including door clearances, turning space, floor loading, and any limits on staging assembled sections.

THE DETAILS MATTER

Project
specifications.

Bring your requirements to the conversation. Final configurations are determined by the project scope and applicable standards.

Specifications and project considerations
ParameterProject consideration
ApplicationSwitchgear Interlocks Explained
Voltage and configurationProject-specific; confirm in quotation
Continuous current and busProject-specific; confirm in quotation
Short-circuit ratingProject-specific; confirm in quotation
Standards and certificationAs applicable; verify for the proposed assembly
Component originAll-American options; confirm in quotation
Lead time and shippingProject-specific; nationwide shipping available
LET'S BUILD SOMETHING

Your project
starts here.

Tell us what you are planning. Share the details you have, and start a conversation about new equipment built for the job.

PREFER TO TALK?
(951) 403-5738
HOUSTON, TEXAS / NATIONWIDE
PROJECT INQUIRY

Request a quote

Fields marked with an asterisk are required.

Submitting opens your email application with your inquiry. Please send the prepared email to complete your request; no information is submitted through this website.

REQUEST A QUOTE